We earn from every qualifying purchase on this website. Read our Affiliate Disclaimer for more info.

Best Leveling Kit For 2018 Silverado 1500

A leveling kit for your 2018 Silverado 1500 can be required for several important reasons. One of the major reasons can be that the Silverado that you have recently purchased has a lower front end compared to its rear side or after some customizations and addition of a bumper the front has become bulkier and hence has lowered down.

Whatever the reason might be, the point is if you have a 2018 Silverado then buying a leveling kit is very much important for precise customization as per your taste. Other than lifting the rear and front end of your wheeler it also explodes the look and appearance of your car.

Now the challenge is, there are numerous brands that offer and claim to manufacture the best leveling kit for Silverado. However, all of them are not genuine and you might fall at a loss after buying them.

So, Because you may be unaware of the subtleties of leveling kits or how to select the ideal one for your 2018 Silverado, we examined and analyzed a selection of leveling kits for your 2018 Silverado.

According to our analysis, the best leveling kit is the Rough Country 2″ Leveling Kit for 2007-2018 Chevy. This article will tell you about the several options available based on your preferences and budget, as well as what to look for when choosing a leveling kit to make your ride look astounding.

So, without further ado, let’s get started on the list.

Best Leveling Kit For 2018 Silverado 1500

All the products mentioned here are available online on amazon.com.

1. Rough Country 2″ Leveling Kit for 2007-2018 Chevy

Pros
  • Alignment is perfect
  • Modifications can be installed with ease
Cons
  • The instructions can be hard to follow

Product details:

  1. Position: Driveline
  2. Material: Aluminum
  3. Maximum Lifting Height: 2 Inches

This package was installed on my 2018 Silverado over the weekend. The installation went quite well, with both sides completed in under an hour combined and without the assistance of a third party. 

I should point out that I did not remove the skid plate or unhook the power steering connector as instructed. I simply unlocked the three higher strut nuts, removed the two lower strut bolts, and loosened the sway bar end link bolt as much as possible while keeping the nut in place. 

The upper control arm ball joint nut was then loosened and tapped to liberate it. I held the front suspension with a floor jack and removed the top ball joint nut before lowering the suspension to separate it from the upper control arm ball joint. 

This allowed me to roll the rotor assembly to the right enough to move the front driveshaft out of the way and drop the new lower strut bolts through. Then, following the directions, I placed the spacers with nuts on the bottom and reassembled everything, reversing the preceding steps. It couldn’t be easier.

I am quite pleased with the result of raising the front height of the truck by 2 1/8″. My factory steps are perfectly 13″ from the step’s bottom, front and back. Please keep in mind that if you use more than 2″ spacers with no lift in the back, your steps will sit higher in the front than in the back.

2. MotoFab Lifts CH-2LM – 2 in Front Leveling Lift Kit

Pros
  • The installation process is easy
  • The parts in the kit are of high-quality built
Cons
  • Might need to remove the shaft for a perfect fit

Product details:

  1. Position: Front
  2. Material: Aluminum
  3. Maximum Lifting Height: 2 Inches

I love my 2015 GMC Sierra Crew Cab too much to mess it up, and I didn’t want to pay pros to do it, so I said what the heck, 100 percent bolt-on, no special skills required except a 15mm wrench, a crescent wrench, and two sockets (18mm and 15mm). 

To begin, the package includes two billet aluminum spacers, four bolts, eight washers, four nuts, and instructions. for simplicity of installation, I saw the video “2010 Rough Country Leveling Kit Install” on YouTube. 

However, there was a lot of pressure when trying to pry the strut up, and it felt like someone was going to get wounded. It didn’t feel right. After about an hour of attempting to watch every moving portion while prying and also observing what is going on. 

Finally, we discovered a critical step missing from the video instructions that would reduce the installation time from 1.5 hours to 20 minutes at most. This kit has now been fitted on a number of trucks and SUVs. 

All of these were simple to make and turned out beautifully! The only way to go is with Motofab. Don’t accept anything less. Other brands have broken parts, missing portions, uneven bolts, lengthy bolts, misthreaded bolts, unthreaded bolts, and so on. 

MotoFab offers an unrivaled Quality Control department that ensures flawless goods.

3. MotoFab Lifts CH-3F-2R 3 in Front and 2 in Rear Leveling lift kit

Pros
  • The truck look is elevated to another level
  • Alignment for both front and rear
Cons
  • The front angles are not correct


Product details:

  1. Position: Rear, Front
  2. Material: Aluminum, Cast Iron
  3. Maximum Lifting Height: 3 Inches

This kit is fantastic for my 2017 Chevy Silverado 1500. The installation was simple and took around three hours for me and a friend to complete. It completely transformed my truck into the aggressive attitude I want, and it rides much better than stock. 

After that, you’ll need an alignment because my truck was reading completely off the charts when I took it into the shop. This kit is well worth the money and I would recommend it to anyone with a Silverado seeking more height and that much desired leveled look.

When it came to installing the rear blocks, the new lift blocks were a simple swap out from the factory ones; just make sure you only do one side at a time or you may have trouble with re-assembly alignment. 

The entire project took me around 4 hours to complete, however depending on your mechanical talents and available tools/equipment, it may take you longer or shorter. It’s useful to have a second set of hands-on hands, especially while reconnecting the front upper control arms to the steering knuckles. 

MotoFab is the way to go if you’re thinking about purchasing a level raise. I would highly recommend this kit and company to anyone wishing to give their truck a fresh look.

4. KSP 3″ Front Leveling Kits for Silverado 1500

Pros
  • Easy installation
  • Allows 3-inch lifting
Cons
  • The only drawback is that the bolts supplied are a touch short.

Product details:

  1. Position: Front
  2. Material: Aluminum
  3. Maximum Lifting Height: 3 Inches

This was installed on my 2019 Silverado after I installed ksp 2-inch raise blocks in the back. When measured from the ground to the top of the wheel well, I’m now the same height as a trail boss. 

If you can remove your struts, you should be able to install this. The only difficulty I had was that the bar at the bottom of the strut needs to be turned 90 degrees because this kit twists the strut assembly 180 degrees. I eventually put the bar on a bench wise and was able to easily move it.

Overall, the installation procedure is simple. You don’t have to remove everything to install it. Simply lower the upper ball joint, remove the 10mm bolt from the brake line, and break away the tie rod. Then remove the three bolts from the strut, leaving the two shock bolts in place. Then use a Jack to reinstall everything.

5. MotoFab Lifts CH-2-2 in Front Leveling Lift Kit

Pros
  • High-quality metal body
  • Angles are perfect
Cons
  • Wiring harness clamps that were previously fastened to factory studs are no longer functional.

Product details:

  1. Position: Front
  2. Material: Aluminum
  3. Maximum Lifting Height: 2 Inches

The term “leveling kit” refers to a variety of various products and sizes The major reason individuals buy them is to lift the front end of their vehicle rather than to level it. In fact, the drive and passenger sides can differ somewhat, and no two vehicles have the same rake from back to front.

Having said that, this kit delivered just what I had hoped for. I don’t like the vehicles’ full stock rake, but I also examined the possibility of additional wear to the front suspension by elevating the front too high.

I chose the 2in because it appeared that it would not push my control arms or CV angles outside of their safe operating ranges. That’s something I’m glad I did. There is a small, virtually insignificant quantity of rake left, which is wonderful for me because I tow on a regular basis. 

There is also enough space between the UCA and the bump stop to allow for travel. Aside from the lift, I really like the machined top strut mount application because it is reasonably hidden and maintains a stock look. The Motofab device appears to be of high quality, readily competing with more expensive alternatives.

6. DEF 2″ Leveling Kit replace 1307 for Chevy GMC 1500

Pros
  • Bolts and other parts are of perfect size
  • Truck looks great
Cons
  • Alignment requires a bit of leverage

Product details:

  1. Position: Front
  2. Material: Aluminum
  3. Maximum lifting: 2 inches

I’m quite happy with how this turned out for my truck. The bolts were exactly the length that they needed to be the hole spacing was a touch closer than the hole spacing on the bottom of the strut, but I found that it was useful since it held the bolts in place while I positioned the strut over top of them. 

Despite being only approximately an inch thick, the spacer elevated the front of my truck by two inches. I can tell the truck is sitting higher, and it looks fantastic. I decided to take a chance on these because I didn’t want to Jerry-rig something myself. 

The space between the holes requires leverage to expand up and align with the truck’s holes. However, with a little force and effort language, they fit perfectly. The truck has been nicely leveled and is ready for new tires. This product is recommended by me.

What to consider while buying a levelling kit?- Buying Guide

While buying a leveling kit there are several factors that must be kept in mind regarding the quality of the product.

Material

The first and most important thing that must be considered is the material of the product. This is most important as if the material is not sturdy enough then it won’t be able to precisely align the truck.

The most favorable material for this product is aluminum. It is corrosion and rust-free and allows great tensile strength to support the car. As per our analysis Rough Country, 2″ Leveling Kit for 2007-2018 Chevy is the most sturdy and well-built leveling kit made from aluminum.

Installation

Installing a leveling kit on your own can be quite difficult especially all by yourself. Hence, the most convenient ones are those that have the right size so that you don’t have to struggle with the fittings and come with a clear instruction manual.

MotoFab Lifts CH-2LM – 2 in Front Leveling Lift Kit as per our reviews is the easiest and well-made leveling kit that one can install without a sweat. The instruction manual is also simple and easy to follow.

Weight limit

This might be one of the most important aspects in this case as we are talking about leveling kits that are specially made for the 2018 Silverado 1500. It is a truck that is quite heavy so it is essential that the kit is sturdy enough to hold the weight efficiently.

Rough Country 2″ Leveling Kit for 2007-2018 Chevy has amazing tensile strength and can hold the truck with ease. It can serve for years without a hitch.

Lift range

This will be as per your choice since individuals might have a specific preference for lifting. Generally, the most sought-after lifting ranges are 2 and 3 inches.

2 inches

For a 2 inches lift to both your rear and front end of the truck, MotoFab Lifts CH-2LM – 2 in Front Leveling Lift Kit can effectively lift the ends.

3 inches

If you want a 3 inches-lift for your truck then don’t hesitate to go for the MotoFab Lifts CH-3F-2R 3 in Front and 2 in the Rear Leveling lift kit.

Our Verdict

A leveling kit for your 2018 Silverado 1500 may be necessary for a variety of reasons. One of the key explanations could be that the Silverado you recently purchased has a lower front end than the back, or that after certain alterations and the addition of a bumper, the front has gotten bulkier and therefore has dropped.

We tried and tested several options on the market to identify the most suitable and well-built leveling kit for your 2018 Silverado. And, based on our analysis, the Rough Country 2″ Leveling Kit for 2007-2018 Chevy is the brightest product of them all. We also talked about the best spark plugs for chevy Cruze 1.5 turbo and 5.7 hemi. So have a look at it too.

Frequently Asked Questions

According to our analysis, the Rough Country 2" Leveling Kit for 2007-2018 Chevy is the best leveling kit for the 2018 Silverado.

Yes, if you install a leveling kit it will affect the mpg as the airflow will be uneven around the framework.

A lift to your truck might be required for several reasons. It might be to enhance the look or to align the ends of the truck. A leveling kit is essentially required for this purpose.

Informny
Logo
Enable registration in settings - general